Error 1722 on updating TherMacam Reporter 8.2 to TherMacam Reporter 8.4

Asked By 0 points N/A Posted on -
qa-featured

Hi everybody,

I am active user of ThermaCam Reporter. Currently I am using ThermaCam Reporter 8.2. I have received information that I can upgrade it to version 8.3. So I tried to get new version but I wasn't shore will it work fine since I have Windows XP professional.

I didn't remove previous version and I run installation. But it was terminated with error message.

I don't know what I did wrong. I could use any help with this problem.

Norman

ThermaCAM Reporter 8 Installer Information

Error 1722.There is a problem with this Windows Installer package. A program run as part of the setup did not finish as excepted. Contact your support personnel or package vendor. Action Install _vstor , location: D:Prerequisites …vstor.exe, command:  /q

 

SHARE
Best Answer by tedeus_amp
Go To Solution
Best Answer
Best Answer
Answered By 0 points N/A #113606

Error 1722 on updating TherMacam Reporter 8.2 to TherMacam Reporter 8.4

qa-featured

Try to do like this :

If your error message includes "O2003PIA.msi" or "O2007PIA.msi",
 
Try the following:
 
1. Open the Microsoft Windows "Control Panel".
2. Open "Add/Remove Programs"
3. For Microsoft Office 2003: Check if "Microsoft Office 2003 Primary Interop Assemblies" is installed.
    For Microsoft Office 2007: Check if "Microsoft Office 2007 Primary Interop Assemblies" is installed.
4. If YES; Uninstall the "Primary Interop Assemblies" manually.
5. Install the "Primary Interop Assemblies" manually. <Reporter installation CD>Prerequisites(O2003PIA.msi or O2007PIA.msi) OR via Office installation.
6. Update your computer via Microsoft Update: Ask your IT department for help if necessary.
7. Install ThermaCAM Reporter. Note that you probably don't need to enter your license key again, just click "next" in the ThermaCAM Licensing Wizard.
If you have Microsoft Office 2003 and your error message includes one of the following install packages: "OTKLoadr.msp", "MSMExtensibility.msi" or "LockbackRegKey.msi";
 
Try the following:
 
1. Update your computer via Microsoft Update: Make sure you have Service Pack 3 for Microsoft Office 2003 installed. Ask your IT department for help if necessary.
2. Install ThermaCAM Reporter. Note that you probably don't need to enter your license key again, just click "next" in the ThermaCAM Licensing Wizard.
 
If your error message includes "E:PrerequisitesMicrosoftvstor.exe",
 
Try the following:
 
1. Start the Control Panel and select Add/Remove Program.
2. Uninstall the program Microsoft Visual Studio 2005 Tools for Office Runtime and Microsoft Visual Studio 2005 Tools for Office Second Edition Runtime.
3. Install ThermaCAM Reporter. Note that you probably don't need to enter your license key again, just click "next" in the ThermaCAM Licensing Wizard.
If all of his is not working 
About tedeus_amp
Questions
0
Answers
2
Best Answers
1
Answered By 0 points N/A #113607

Error 1722 on updating TherMacam Reporter 8.2 to TherMacam Reporter 8.4

qa-featured

Hi Noorman,

To fix 1722 error, follow the steps below.

Solution 1 :

If you get the error "X:Prerequisites …vstor.exe"( X means disk drive you are using ), try the following solution :
 
1. Open Control Panel and Select Add/Remove Programs.
2. Find Microsoft Visual Studio 2005 Tools for Office Runtime and Microsoft Visual Studio 2005 Tools for Office Second Edition Runtime and uninstall them.
3. After that, install ThermaCAM Reporter. 
 
Solution 2:
 
If it doesn't work, you can try the following :
 
1. Open "Control Panel"
2. Select "Add/Remove Programs"
3. Look if  Microsoft Office 2003 Primary Interop Assemblies is installed, if not install the assemblies.
And for Microsoft Office 2007, find if the binaries of Microsoft Office 2007 Primary Interop Assemblies is installed. Install the binary if it is not installed otherwise ThermaCAM won't work.   
4. After that, apply the attached file Fix1722.exe
 
Hope this can help.
 
Regards
 
Kean
About kean b
Questions
1
Answers
5
Best Answers
2

E-TDS validation utility upload file error

Previous

Ultimate Windows Tweaker update error

Next

Related Questions