Hello geeks,

I am trying to install NSIS (Null Soft Scriptable Installer System) on my pc, which is an open source windows based installer system for the distribution of the applications.

Whenever I start the installer, it presents the following error.

NSIS Error

The installer you are trying to use is corrupted or incomplete.

This could be the result of a damaged disk, a failed download or a virus.

You may want to contact the author of this installer to obtain a new copy.

It may be possible to skip this check using the /NCRC command line switch

Hi,

Joint Test Action Group JTAG Test Access Port and Boundary-Scan Architecture.

It is a serial bus with four signals:

• TCK(Test Clock)
• TMS(Test Mode Select)
• TDI(Test Data Input)
• TDO(Test Data Output)

The bus is used as a test bus for the Boundary-Scan of ICs, as in Design-For-Testability.

For my official project, whenever I test the circuit with it, I got the following error.

JTAG test failed

Failed – TDO changes, but TDI pattern does not match.

Try the following hints to fix the problem:

Hi guys,

I am using windows XP home edition and I have an imate KJam windows mobile phone. I just formatted my C drive and did a clean install. After that I'm unable to connect my mobile with my PC. It was working just fine before the re installation, hence there is no fault in mobile / connectivity cable.

I was using active sync version 4.5 in previous windows installation and using the same this time. Whenever I tried to connect my mobile with the data cable attached to the system, it gives me the following error.

Microsoft ActiveSync

Hi folks,

I am using a Dell laptop with Windows OS installed.

I observed that, when starting new programs gets started automatically and my screen resolution changes with desktop icons and size. 

The screen resolution changes form 1024 x 768 to 640 x 480. Although I can changes those setting ,but unable to save them and make them stay. This happens every time I boot my system.

I have an ATI Rage 128 Ultra Video Card and the also updated Video Drivers. I believe the Video card driver is working fine.

I tried my best in getting screen resolution but unable to save those settings.

I have no clue and if someone can suggest me how to get this done.

Thanks.

Hi,

Hi,

I had a problem closing some application. Whenever I open application error will occur, a message will pop up. Just like a while ago I quit internet explorer, the error message the memory could not be read. This started after i failed to shut down my computer with microsoft Windows XP home due to hang up problem.

. Iexplore.exe – Application Error

The instruction at “0x2753a7d0” referenced memorry at “0x2753a7d0”. The memory could not be “read”.

Click on OK to terminate the program

Hi,

I am using Cisco AnyConnect VPN Client, to connect to our corporate VPN connection. When I was about to connect  it fails to connect. An error message pops up that says, "unable to establish VPN connection".

Cisco AnyConnect VPN Client

Unable to establish VPN

First thing I did was, to check  my LAN connection.  It was connected, and as I refer to other computer, it can connect.  

After much isolation on network connections and hardware aspects, I run out of  ideas to where I shall I look in to connect to the VPN.

Thank you all.

Hi,

There are some instances in my computer under windows home edition that I cannot understand. Whenever I want to run my internet explorer it won't load. Error will pop up to the screen that says application failed,

Iexplore – Application error

The application failed to initialize properly (0xc0000142). Click OK to

Terminate the application.

Hello all,

I was using Internet explorer 8, and a friend of mine told me about Internet Explorer 9. I downloaded it from a site. When I try to install, it fails to install. It suggest some error, that the computer might have some recent version installed. The error came about after 40 percent of the installation. I tried to install it again, after restarting my computer.

By the way I am using windows 7, same problem occurs after about, 40 percent of the installation process. So, I downloaded another copy and installed it again. Still the same error occurs after about 40 percent of the installation process is complete.

Hi,

I am posting here regarding my browser Internet Explorer error.

Whenever I use WordPress for my blogs and forums, I always encounter this message regarding script,

Windows Internet Explorer

Stop running this script?

A script on this page is causing Internet Explorer to run slowly.

If it continues to run, your computer may become

unresponsive.