Hi Experts,

I am having a small network at the office. I have to find a single word domain. I configured DNS server but could not achieve this. Any networking expert may help me. I have installed Windows Server 2007 on my desktop. There are 10 computers as clients. Thanks.

Regards,

Roger Neil

Hi Experts,

I am in need of how to combine files from two pc. I know that this can be achieved by using UTP cable. First connect to PC then configure IP's. But do not know the exact IP configuration. Any expert can help me. Thanks.

Regards,

Mich Baker

Hi,

We used E2007 before and at this moment we are using E2010 on Hyper-V in an Exchange environment with just a single server. The mail is working well and mailboxes have been moved fruitfully. At the moment of deleting a message in Outlook ’10 then basically shifts to the deleted folder and then we got an error shown “there are sync issues and that the sync has failed” as soon as we make the deleted folder empty. The installation is totally ok as well as we have deleted profiles. I think this trouble would not be seen if the mode of cache is not considered to use in Outlook. Total memories of the mailboxes are almost 1 to 1.25 gigabytes. Thank you

I’m currently in the middle of developing a software for Windows 7 64 bits, which will be able to know the ports being used by running software. It is possible with netstat remote, but I was wondering if there is a way to execute commands for another client, remotely?

Hello TechyV buddies!

I am having some problem with our ESXi 4.1.0 hosts. The management network is not enabled.

If I try to enable the management network an error occurs.

The error message is this: "Operation on the management network interface failed"

Although the management network is disabled I can still do a ssh connection via management network interface IP address. This is because there is no connection via vsphere client o the vcenter.

How can I configure this problem?

Can I restart the management network?

Is there any other way not to restart the host server?

Can anyone help me solve this issue?

Hello Techyv buddies!

I am having some trouble with the Terminal Services-Remote connection Manager. A self-signed certificate is needed to be used by the Terminal Server authentication when connecting to SSL which fails to create by the terminal server.

The key that is relevant to the status code is not valid to use in the in the certain state.

Here are the following problem that shows:

Log name: system

Source; Terminal Services – remote Connection Manager

Event id: 1057

Keywords: classic

OpCode: info

Any help will greatly be appreciated.

Hello Techyv buddies,

I am having some problems regarding the use of Cognos 10.1 and Internet Explorer 8. As we use Internet explorer 8 in accessing cognos these problems are being encountered:

Contents in the Cognos Connection will hide new items. Network error (tcp_error) in the middle of executing the report and some items while opening the report studio. MES_XML_LOADSTRING_ERRO while opening/creating reports in Analysis Studio.

I am not so sure the causes of these recurrent problems. We tried to seek the help f IBM and what they give was a generic solution. We were advice to upgrade to 10.1.1 or install a fix pack.

Hi!

I am having some trouble when I open my personal website. I am not very good in IT so I really need a good help in this matter. Every time I open my website, an error message keeps on showing, and It goes like this:

“Network Error (tcp_error)

A communication error occurred: “Operation timed out”

The Web Server may be down, too busy, or experiencing other problems preventing it from responding to

For instance, contact your network support team.”

What could be the causing problem to this error? I will give more info about the problem if asked. I am looking forward for any good solutions to my problem. Thank you TechyV buddies.

Hi friends

I am using the HA setup of AMX BPM1.2 HFO1. I had to change the emergency management services (EMS) transport to a fault tolerant system. I also changed the EMS connection string in AMX GUI. After I changed the string, AMX BPM is not properly initializing. I tried to fix it by undeploying it and also by removing all the deployed applications. I also cleared all the server queues but still ended up in the same problem.

When I deployed the AMX.BPM.APPP I got a warning message. The warning message said:

The system has discovered the following issues that need to be resolved in order to process your request.

Hello

I am trying to establish a connection with the database. To carry out this task a new data source is required to be created. In this context I have turned the windows firewall off and the project wise client network configuration  settings are set as blank as it is in the same subnet mask.

I was able to create a data source yesterday from another user account but unfortunately today when using another account I cannot create a data source. I get the following error on my screen:

Could not connect to datasource because of the following problem: